Mobile phone detector MB-DET Mobile phone detector, GPS trackers, Wifi devices detector. MB-DET looks like a mobile phone but it is a mobile phone detector that can detect any mobile phone or Wifi device within 10 to 15 meters. This device is used to detect mobile phones in a prison but it can also detects GPS trackers, wireless microphones and cameras. As soon as a mobile phone or GPS tracker is used, the detector vibrates and indicate the signal strength and the frequency band used. This device detects the uplink frequencies of mobile phones and GPS trackers.   Main characteristics : • Detects the following frequencies: CDMA 450 GSM 900 DCS 1800 UMTS/3G DECT Bluetooth and Wifi devices (wireless microphones and cameras) Cordless phones Analog and digital transmitters • Bar graphe indicates the signal strength and the frequency band • Adjustable sensitivity • Integrated vibrator (no sound alarm) • Operating time: 4 days • Temperature: -10 to 50°C Power supply: • Internal battery rechargable through USB cable or any 5v AC/DC adapter • AC/DC adaptor: 110/220v Dimensions: • 108 x 47 x 12,7 mm • Weight: 66g Downlod the Documentation   MB-DLF Frequency Detector / Localizer MB-DLF is a detector designed to identify and locate radio transmitting equipments. This device can detect cellphones, cordless phones, Bluetooth and Wifi devices, analog or digital transmitters, GPS trackers, wireless cameras and wireless microphones. A soon as a signal is detected, MB-DLF will display the frequency band, the signal strength and will help finding the location of the transmitting equipment. MB-DLF detects the uplink frequencies of mobile phones. Main Characteristics: Selective RF detector: CDMA 450 GSM 900 DCS 1800 UMTS/3G DECT Bluetooth and Wifi devices (wireless microphones and cameras) Cordless phones Analog and digital transmitters • Frequency range: 50 - 3.300 MHz • Sensitivity: 70mV / m • Dynamic range: 50 dB • Bandwidth: 10 MHz • Running time: 3 to 12 hours (depending on the mode) • Operating temperature: -10 à 40°C Power supply: • Internal battery (Lithium Polymere) Dimensions: • 77 x 43 x 18 mm • Weight: 35 g Download the User Manual   Non linear junction detectors NLJD-01 Non linear junction detector Non Linear Junction Detector represents a unique equipment capable to find out practically all concealed eavesdropping devices though the analysis of harmonic emissions caused by an illuminating signal when it is reflected off of a target. SPECIFICATIONS Power supply - Accumulator (7,2 V) Continuous operation time - Not less than 4 h. The transmitter operates in a pulse mode in a frequency range 915 MHz Spacing of retuning 200 KHz> Maximum impulse output power 16 V±1 Db Minimal impulse output power 1,6 Db Receivers adjustment frequencies are equal to double or triple transmitter frequency accordingly. Both receivers sensitivity at signal/noise ratio not less than 6 Db -136 Db/W Receiver dynamic range not less than 30 Db Manual receivers amplification control in 4 steps; each step equals to (10±1) Db In a "20K" mode of operation both receivers emits signals modulating radio-frequencypulse pattern. Demodulated signal bandwidth 500-2000 Hz. There are three aerials combined in one unit. Beam Width Angle (at 3 Db level on transmitting and receiving aerials) not more than 90. All aerials are circular polarized. Download the documentation NLJD-02 This small-sized nonlinear device is intended for detection of transceiving and radioelectronic facilities including cellular telephone SIM Cards, dictaphones, etc. Only Second harmonics.  Range of coverage – from 10 mm to several meters (depending on the device type detected). Technical specification Type of signal– impulse, continious; Effective transmitting output – 0,5 W; Receivers sensivity -150 Db/W; Transmitter operating frequency - 2400 MHz; Free channel selection – automatic; Power flux density in the scanning area vector– not more than 200 μW/cm; Dynamic range– 80 Db; Transmitting and receiving antennaes - circular polarized; Working time in impulse mode – about 2,5 hours; Working time in continious mode – not less than 2 hours; Automatic discharging control indication; Charging time – 2 hours; Weight – not more than 350 grams; Dimensions– 220 х 90 х 90(30) mm; Battery – Li-Ion accumulator; Operating temperature - from -10 to +40°С; Download the documentation NLJD-03 NLJD-03 is a multifunctional device, which is ready to work as metal detector and non-linear junction detector at the same time. Non-linear junction detector is mounted inside the standart shell of the hand-held metal detector (F.ex. Garrett Super Scanner). No visual signs of non-linear junction detector. Indication of the threats found by non-linear junction detector is showing through the standart metal detector indicators/LEDs. Specification (common): Working Temperatures - from +5 till  +40°С Weight – not more than 1 kg (total weight including the weight of original device) Dimensions - 83 х 413 х 420 mm Power source - Li-Ion battery 1,2 A/h х 7,2 V Working Time - approximately 4 hours Automatic control of the battery level Time of charging– 1 hour Headphones/charging jack Humidity: up to 95% without direct condensing on the device Specification for the non-linear junction detector: Effective impulse output power  – 3 W +/- 1,5 Db Sensivity of the receiver -120 Dbm Specifications for the metal detector:  Working Frequency- 93 кHz Optimum distance to find steel objects – 0,10-0,15 m Light and sound alarm indication; buzzer: 2 kHz (Metal) -1,5 kHz (electronic components) Tuning - Automatic Download the documentation   Up